Essential Plumber Tips for Installing a Bathtub
Essential Plumber Tips for Installing a Bathtub
Blog Article
Everybody may have their unique piece of advice when it comes to Installing A Bathtub.
Installing a bath tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a new one is additionally a reasonably challenging task. If the old bathtub is conveniently easily accessible, the job can move easily; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and also set in the new one. Make certain you have actually certified yourself for the job and fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will aid you set up a brand-new tub in your washroom if you have actually already acquired a brand-new tub as well as do not need to change the plan of your previous supply of water pipelines.
Your tools as well as material checklist need to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area in between the tap as well as the sink. Secure the tap in position with the supplier supplied backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind must be connected to the tap ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the required position. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water supply and also check all joints and also new pipework for leaks and also tighten them if needed. Fill up the bath tub as well as additionally examine the overflow outlet and the normal outlet for leakages.
Finally, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub must wait until the bath tub has been utilized at the very least when as this will settle it into its last setting.
Planning for the Installment
Firstly, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very intrigued by Tools You Need to Install a New Bathtub and I'm hoping you appreciated the piece. Liked our post? Please share it. Help another person locate it. Thank-you for going through it.
Hot water gone? Call. Report this page